Roof in Disrepair? Follow These Experts Tips for Installing New Shingles (2022)

  • Home Improvement Ideas
  • Home Exteriors
  • Roofs

Is your roof in disrepair? It's possible to shingle over shingles, to lay new shingles over existing ones and avoid the cost of a tear-off.

By

Caitlin Sole

Roof in Disrepair? Follow These Experts Tips for Installing New Shingles (1)

Caitlin Sole

Caitlin Sole is the senior home editor at BHG. She is a writer and editor with nearly a decade of interior design expertise. She has vast experience with digital media, including SEO, photo shoot production, video production, eCommerce content, print collaboration, and custom sales content.

Learn about BHG's Editorial Process

Updated on June 10, 2022

Roof in Disrepair? Follow These Experts Tips for Installing New Shingles (2)

Project Overview

  • Working Time:1 day
  • Total Time:1 day
  • Skill Level:Advanced

If conditions are right, new shingles laid over old ones can be just as attractive and durable as shingles laid on bare sheathing. Installation is easier than for a tear-off job, since you can use the existing shingles as guides for laying the new ones. However, you must take care to install shingles correctly so they lie flat. And a good job involves installing new flashings rather than relying on the existing ones.

Reroofing jobs are sometimes done without replacing flashings. However, installing new flashings, including special drip-edge flashings made for reroofing, will ensure a tight seal and a long life. Some roofers install a layer of waterproof shingle underlayment (WSU) over the existing shingles at the eave end, as would be done for a roof laid on bare sheathing. This provides added protection against ice dams.

Asphalt shingles can be laid over cedar shakes or shingles, but this is a roofing project best left to the pros. Beveled wood pieces called "horsefeathers" must be laid along the thick edges of the shakes to make a fairly flat surface. Before you reshingle a roof, read our step-by-step guide for adding new shingles over old ones.

Equipment / Tools

  • 1Power nailer or roofing hatchet
  • 1Tape measure
  • 1Roofing shovel or flat pry bar
  • 1Hammer
  • 1Drill
  • 1Carpenter's square
  • 1Straight-cut tin snips
  • 1Utility knife
  • 1Chalkline
  • 1Broom

Materials

  • 1Roof cement
  • 1Flashing
  • 1Nails for flashing
  • 1WSU sheet
  • 1Shingles
  • 1Nails long enough to penetrate sheathing

Instructions

Roof in Disrepair? Follow These Experts Tips for Installing New Shingles (3)

  1. Remove Caps

    Start by removing the ridge caps. Doing it now will make it easier to keep the reroofing job clean. Use a flat pry bar or roofing shovel to pry out and remove the ridge shingles. Remove all the nails.

    Roof in Disrepair? Follow These Experts Tips for Installing New Shingles (4)

  2. Remove Obstructions

    Remove air vents and pipe flashings by prying out or unscrewing the fasteners holding the fixtures. If you damage shingles while doing this, repair them (see next step). Reuse a vent or flashing only if it is like new; otherwise, replace it with a new one that will fit the hole or pipe.

    Roof in Disrepair? Follow These Experts Tips for Installing New Shingles (5)

    (Video) 5 Most Common Mistakes in Shingle Roofing
  3. Repair Broken Shingles

    If a shingle is torn or cracked, glue the broken piece back in place using roofing cement. If the broken piece is lost, cut a new piece to fit the existing shingle. The goal is to provide a reasonably flat surface for the new shingles to lie over, with no gaps greater than 1/2 inch.

    Roof in Disrepair? Follow These Experts Tips for Installing New Shingles (6)

  4. Sweep the Roof

    Using a large broom, brush away all the broken shingle pieces, twigs, and any other debris that could become trapped under the new shingles that you'll install. Keep the roof clean as you work.

    Roof in Disrepair? Follow These Experts Tips for Installing New Shingles (7)

  5. Install Flashing

    At the eave and the rake, install U-shaped drip-edge flashing made for reroofing jobs. Install the eave piece first, then the rake piece over it. The two pieces should meet neatly at the corners. Drive nails at high points on the underlying roof, the bottoms of the shingles.

  6. Install Valley Flashing

    If you have an open valley, install new W-shape metal or vinyl valley flashing to fit directly over the old flashing. Attach it by driving nails into the outside edges only. Do not drive nails less than 6 inches from the center of the flashing.

    Roof in Disrepair? Follow These Experts Tips for Installing New Shingles (9)

  7. Install Starter Strip

    Use a starter strip or cut pieces for a starter course. Rip-cut the starter strip or starter pieces so that they butt up against the second course of existing shingles and are even with the front edge of the existing roofing. Attach with nails along the top edge of the strip.

    Editor's tip: If the existing roof has wavy horizontal lines, you can take out the waves by snapping a horizontal line a 1/2 inch below the shingle bottoms of one course. Install a course along the snapped line, then install succeeding courses using a guide or a snapped line.

    Roof in Disrepair? Follow These Experts Tips for Installing New Shingles (10)

  8. Cut and Install Shingles

    Rip-cut the shingles for the first course so they butt up against the third course of existing shingles and are even with the front edge of the starter course. Their tab slots should not line up with the tab slots of the starter course, if there are any. Nail the shingles just above the tab slots.

    Editor's Tip: The thicker the new shingle, the better it will hide any imperfections in the roofing underneath. It's a good idea to use at least 40-year shingles; architectural shingles are an even better choice.

    Roof in Disrepair? Follow These Experts Tips for Installing New Shingles (11)

  9. Continue Installing Shingles

    Butt the succeeding courses of shingles against the bottoms of existing shingles and apply them by driving nails above the tab slots. Snap vertical control lines; there is no need to snap horizontal lines. Be sure the new tab slots do not align with the old ones.

    Editor's tip: In a reroof job, the starter course (or strip) is rip-cut so it butts up against the third course of the existing shingles. Its front edge is even with the front edge of the drip edge. The rest of the shingles are full width.

    (Video) How to Replace or Repair a Damaged Shingle by RoofingIntelligence.com

    Roof in Disrepair? Follow These Experts Tips for Installing New Shingles (12)

  10. Work Around Vent

    Once you've installed shingles just past a plumbing vent, install the flashing piece so it will lie on top of roofing at its bottom, but be covered with roofing at its top. Depending on the width of the pipe, you may need to tear away a segment or two of the rubber boot. Apply roofing cement, slide the flashing over the pipe, and push so it lies flat on the roof.

    Roof in Disrepair? Follow These Experts Tips for Installing New Shingles (13)

  11. Install Air Vents

    Install air vents in a similar manner. For both plumbing-vent flashing and air vents, you'll need to cut the shingle above to go around the flashing and then install the shingle.

    Roof in Disrepair? Follow These Experts Tips for Installing New Shingles (14)

  12. Work Around Walls

    Where you meet a chimney or side wall, install step flashing. Apply a shingle, then a piece of flashing, then a shingle, and so on, so that each piece of flashing rests on top of the lower course and is covered by the upper course. You'll need to pry the siding outward to slip in the flashing; in some cases, you'll have to remove the siding.

  13. Install Counterflashing

    Protect the step flashing with counterflashing. On a chimney, use a grinder to cut an indentation into the mortar. Cut and bend the counterflashing to fit snugly into the cut mortar and to cover at least 3 inches of the step flashing. Apply mortar with a caulking gun and set the flashing into the mortar.

    Roof in Disrepair? Follow These Experts Tips for Installing New Shingles (17)

  14. Cover Ridge

    Install roofing on both sides of a ridge and cut them so they butt closely together but do not overlap. Cut shingles into ridgecaps. Snap lines on either side and install the caps.

    Roof in Disrepair? Follow These Experts Tips for Installing New Shingles (18)

  15. Cut Shingles

    At the rake, snap a line directly above the edge of the existing shingles. Cut with a utility knife; you might want to use a straightedge. You might find it easier if you first cut from below, using the existing shingles as a cutting guide.

    (Video) How to Install Starter Strip | Shingle Roof Install Guide

(Video) How to Install Roof Shingles | Ask This Old House
Related Articles
How to Install 3-Tab Roof ShinglesHow to Install Roll RoofingYour Step-by-Step Guide to Installing Cedar Shake SidingHow to Apply Underlayment to a RoofHow to Install Plumbing Vent Lines in Your BathroomHow to Install Modified-Bitumen RoofingHow to Install a Bathroom Vent FanHow to Install Flashing Around Windows and Doors to Protect Against Leaks
How to Repair Vinyl SidingHow to Build a DIY Brick Outdoor KitchenHow to Complete a Window Glass Replacement Efficiently and SafelyChoose the Best Exterior Material With Our Guide to House Siding OptionsYour Guide to Troubleshooting Door ProblemsHow to Lay Mortared Brick on Front StepsHow to Install a Whirlpool TubHow to Build a Doghouse

FAQs

How do you prep a roof for shingles? ›

But you can see here i got pretty much all my nails. So here i'm just tacking the corner. Everything

Is a hole in the roof an emergency? ›

Having a hole in your roof, even a tiny one, can pose serious dangers if you don't get it fixed urgently: Roof material damage: Even a few drops of water penetration can damage the roofing materials, causing your hole to get bigger, incurring more expensive repair costs.

How do I temporarily fix a leaky roof? ›

Temporary Fixes For a Leaking Roof
  1. Tarps. Tarps are one method of temporarily fixing a leaking roof. ...
  2. Roof cement, silicone and sealant. Using roof cement, silicone or a rubber sealant could also work as a temporary fix for your leaking roof. ...
  3. Replace the tile or shingle.
31 Jan 2022

Videos

1. How to Install Valley Flashing | Shingle Roof Install Guide
(Roof Repair Specialist)
2. Roofing tips: How to know “if” you need a new shingle roof installation or not?
(South County Roofing - Tile Roof Repair Specialist)
3. How We Install Asphalt Shingles | Part 1 | Boston MA | CAN Roof Construction
(CAN Roof Construction - Boston Roofing Contractor)
4. The CertainTeed Integrity Roof System | CAN Roof Construction
(CAN Roof Construction - Boston Roofing Contractor)
5. How We Install Asphalt Shingles | Part 2 | Boston MA | CAN Roof Construction
(CAN Roof Construction - Boston Roofing Contractor)
6. Testimonial | Gutter Replacement & Roof Repair | Somerville MA | CAN Roof Construction
(CAN Roof Construction - Boston Roofing Contractor)

Top Articles

Latest Posts

Article information

Author: Amb. Frankie Simonis

Last Updated: 12/27/2022

Views: 6162

Rating: 4.6 / 5 (76 voted)

Reviews: 91% of readers found this page helpful

Author information

Name: Amb. Frankie Simonis

Birthday: 1998-02-19

Address: 64841 Delmar Isle, North Wiley, OR 74073

Phone: +17844167847676

Job: Forward IT Agent

Hobby: LARPing, Kitesurfing, Sewing, Digital arts, Sand art, Gardening, Dance

Introduction: My name is Amb. Frankie Simonis, I am a hilarious, enchanting, energetic, cooperative, innocent, cute, joyous person who loves writing and wants to share my knowledge and understanding with you.